Lista przedmiotów z materiałami udostępnionymi dla studentów

Dla_studentów
  • Increase font size
  • Default font size
  • Decrease font size

Jarosław Kuciński

Laboratoryjny zasilacz regulowany z komunikacją z komputerem


Laboratory power supply controlled by means of PC


Opiekun pracy dyplomowej: dr inż. Marcin Kociołek
Praca dyplomowa inżynierska obroniona 2013-02-18
Streszczenie pracy dyplomowej:
Większość układów elektronicznych wymaga zasilania. Różnorodne układy wymagają odpowiednich napięć zasilających. Zasilacz laboratoryjny jest jednym z podstawowych narzędzi inżyniera elektronika. Niniejsza praca przedstawia projekt, montaż oraz uruchomienie zasilacza laboratoryjnego sterowanego cyfrowo. Zasilacz posiada jedno wyjście o regulowanym napięciu w zakresie od 1.25-30V oraz prądzie do 3A, i trzy wyjścia o stałych napięciach 3.3V, 5V i 12V, i prądzie maksymalnym 3A. Zasilacz zbudowano w oparciu o przetwornice impulsowe step-down. Pracą urządzenia steruje mikrokontroler ATmega32. Ustawianie napięcia wyjściowego odbywa się za pomocą dedykowanych mikroprzełączników lub zdalnie za pomocą komputera PC poprzez interfejs USB. Wartości napięcia oraz prądu wyjścia regulowanego wyświetlane są na wyświetlaczach diodowych. Mikrokontroler steruje stabilizatorem impulsowym poprzez potencjometr cyfrowy. Elementy mocy są chłodzone aktywnie za pomocą radiatora z wentylatorem. Prędkość obrotowa wentylatora ustalana jest na podstawie temperatury radiatora. Wszystkie schematy i płytki PCB oraz symulacje, wykonano w programie ®Altium Designer. Niniejsza praca składa się z sześciu rozdziałów. Pierwszym rozdziałem jest wstęp, w którym przedstawiono wybór i opis tematyki pracy. W drugim rozdziale znajdują się zagadnienia teoretyczne, związane ze stabilizatorami napięcia. Trzeci rozdział przedstawia opis interfejsów komunikacyjnych, poprzez które komunikują się układy cyfrowe. Czwarty rozdział jest poświęcony budowie i działaniu zasilacza laboratoryjnego. W piątym rozdziale przedstawiono symulacje zmontowanego zasilacza. Ostatni, szósty rozdział, przedstawia podsumowanie celu niniejszej pracy.
Abstract:
The majority of electronic circuits requires power supply. Different circuits require appropriate supply voltages. Laboratory power supply is one of the most important tools for electronic engineer. The thesis presents the design, the assembly and the first start of the digitally controlled laboratory power supply. The power supply is equipped with one controlled voltage output and three constant voltage output. The controlled voltage output has the range of 1.25-30V and the maximum current of 3A. Constant voltage outputs have voltages of 3.3V, 5V and 12V respectively and the maximum output of 3A each. The power supply was built by means of step-down switching regulator. The control section of the device is based on the ATmega32 microcontroller. The output voltage is set locally by means of micro switches and remotely by means of PC. The voltage and the current of controlled voltage output are shown on a LED displays. The microcontroller controls the output voltage by means of the digital resistor placed in the control circuit of switching regulator. The cooling system consist of the radiator with a fan. The rotation speed of the fan is controlled based on radiator temperature. All schematics and PCB were created and simulations were performed by means of ®Altium Designer. This document consists of six chapters. The first chapter is an introduction. The second chapter provides theoretical issues associated with voltage stabilizers. The third section provides a description of the interfaces utilized in digital systems. The fourth chapter is devoted to the construction and operation of the laboratory power supply. In the fifth chapter simulations of assembly issues were presented. The last chapter is the summary.